Differences

This shows you the differences between two versions of the page.

--- cp:start [2015/12/03 07:14] – [Control System] Alan Shea
+++ cp:start [Unknown date] (current) – external edit (Unknown date) 127.0.0.1
@@ Line 2: / Line 2: @@
 {{ :cp:c61-genset-control-tower-3p.jpg?401|}}
-The unified control system uses ComAp [[http://comap.cz/products/detail/intelicompact-nt-mint/|InteliCompact]] series generator controllers. These controllers allow full control of all generator functions in a non-proprietary architecture. The system can control basic gensets (all sensors etc direct wired) or communicate with many computer controlled gensets directly through a CAN network. (Note: Some gensets with built in proprietary controls will not interface with the ComAp products--contact [[http://www.comapllc.com|ComAp]] for specific information).
+The unified control system uses ComAp [[http://comap.cz/products/detail/intelicompact-nt-mint/|InteliCompact]] series generator controllers. [**//Replaced with [[hhttps://www.comap-control.com/products/controllers/paralleling-gen-set-controllers/inteligen/inteligen4-200/|InteliGen4 200]] Controller//**] These controllers allow full control of all generator functions in a non-proprietary architecture. The system can control basic gensets (all sensors etc direct wired) or communicate with many computer controlled gensets directly through a CAN network. (Note: Some gensets with built in proprietary controls will not interface with the ComAp products--contact [[http://www.comap.cz|ComAp]] for specific information).
-The system also uses a [[http://comap.cz/products/detail/mainscompact-nt/|MainsCompact]] to interface with local utility or an auxiliary power source -- for instance, a portable generator used for extremely low usage times.
+The system also uses a [[http://comap.cz/products/detail/mainscompact-nt/|MainsCompact]] to interface with local utility or an auxiliary power source -- for instance, a portable generator used for extremely low usage times. [**//Replaced with [[hhttps://www.comap-control.com/products/switchgear-control-and-protections/mains-controllers/intelimains-210-g2/|InteliMains 210 G2]]//**]
 The system is capable of running any one source, or all sources paralleled together at once. It can start, run, and stop generators from a remote location (such as a surgery building or operating room), or automatically as the load fluctuates. It also will monitor fuel levels and alarms and provide audible and visual warning of needed service.
@@ Line 14: / Line 14: @@
 However, if an application plans to use proprietary gensets (such as Cummins PowerCommand), and does not need the paralleling function, a simple switch panel can replace the entire control tower in the overall design.
-Contact [[:reference:Martin Machinery]] as the preferred supplier for the control system. It can be assembled and tested along with the generators before shipping. {{ :cp:img_5133.jpg?300|Control Panel as built by Martin Machinery}} [[Martin Control Panel Pictures]]
+Contact [[:reference:Martin Energy]] as the preferred supplier for the control system. It can be assembled and tested along with the generators before shipping. {{ :cp:img_5133.jpg?300|Control Panel as built by Martin Energy Group}} [[cp-pictures]]
 For very detailed and in-depth information on generator paralleling systems, see [[http://cumminspower.com/www/en/technical/application/t-016.pdf|Cummins Power Paralleling Application Manual]] (PDF) and other useful Application Manuals at http://cumminspower.com/en/technical/application/index.jsp.
+\\
+<wrap center round alert 250px>
+** See Warnings below  **
+</wrap>
+\\
 ===ZIP Archives===
@@ Line 43: / Line 50: @@
 {{filelist>:cp:*.gen&style=table&tableheader=1&tableshowdate=1&tableshowsize=1}}
   * Edit with [[:Teco PLC SG2]] Software (v3.22)
+\\
+{{page>:warning&nofooter}}

MetaTek

User Tools

Site Tools

Differences

Page Tools